Fault-Tolerant CAN/LIN Fail-Safe System Basis Chip

查看产品图片

产品详情

选择区域:

Features

2.1 General
  • Contains a full set of CAN and LIN ECU functions:
    • CAN transceiver and LIN transceiver
    • Voltage regulator for the microcontroller (3.3 V or 5.0 V)
    • Separate voltage regulator for the CAN transceiver (5 V)
    • Enhanced window watchdog with on-chip oscillator
    • Serial Peripheral Interface (SPI) for the microcontroller
    • ECU power management system
    • Fully integrated autonomous fail-safe system
  • Designed for automotive applications:
    • Supports 14 V, 24 V and 42 V architectures
    • Excellent ElectroMagnetic Compatibility (EMC) performance
    • ±8 kV ElectroStatic Discharge (ESD) protection Human Body Model (HBM) for off-board pins
    • ±6 kV ElectroStatic Discharge (ESD) protection IEC 61000-4-2 for off-board pins
    • ±60 V short-circuit proof CAN/LIN-bus pins
    • Battery and CAN/LIN-bus pins are protected against transients in accordance with ISO 7637
    • Very low sleep current
  • Supports remote flash programming via the CAN-bus
  • Small 6.1 mm × 11 mm HTSSOP32 package with low thermal resistance

CAN transceiver

  • ISO 11898-3 compliant fault-tolerant CAN transceiver
  • Enhanced error signalling and reporting
  • Dedicated low dropout voltage regulator for the CAN-bus:
    • Independent from microcontroller supply
    • Guarded by CAN-bus failure management
    • Significantly improves EMC performance
  • Partial networking option with global wake-up feature, allows selective CAN-bus communication without waking up sleeping nodes
  • Bus connections are truly floating when power is off
  • Ground shift detection

LIN transceiver

  • LIN 2.0 compliant LIN transceiver
  • Enhanced error signalling and reporting
  • Downward compatible with LIN 1.3 and the TJA1020

Power management

  • Smart operating modes and power management modes
  • Cyclic wake-up capability in Standby and Sleep modes
  • Local wake-up input with cyclic supply feature
  • Remote wake-up capability via the CAN-bus and LIN-bus
  • External voltage regulators can easily be incorporated in the power supply system (flexible and fail-safe)
  • 42 V battery-related high-side switch for driving external loads such as relays and wake-up switches
  • Intelligent maskable interrupt output

Fail-safe features

  • Safe and predictable behavior under all conditions
  • Programmable fail-safe coded window and time-out watchdog with on-chip oscillator, guaranteeing autonomous fail-safe system supervision
  • Fail-safe coded 16-bit SPI interface for the microcontroller
  • Global enable pin for the control of safety-critical hardware
  • Detection and detailed reporting of failures:
    • On-chip oscillator failure and watchdog alerts
    • Voltage regulator undervoltages
    • CAN and LIN-bus failures (short-circuits and open-circuit bus wires)
    • TXD and RXD clamping situations and short-circuits
    • Clamped or open reset line
    • SPI message errors
    • Overtemperature warning
    • ECU ground shift (two selectable thresholds)
  • Rigorous error handling based on diagnostics
  • 23 bits of access-protected RAM is available e.g. for logging of cyclic problems
  • Reporting in a single SPI message; no assembly of multiple SPI frames needed
  • limp-home output signal for activating application hardware in case system enters Fail-safe mode (e.g. for switching on warning lights)
  • Fail-safe coded activation of Software development mode and Flash mode
  • One SPI readable device type identification
  • Software-initiated system reset

设计资源

选择区域:

文档

快速参考 文档类别.

3 文件

支持

您需要什么帮助?