Port M wired-Or mode register, WOMM, should be read at address 0x257

instead of address 0x256. Any read to address 0x256 will return an error

of 0x00.

 

If WOMM is required to be read it should be done at address 0x257.

 

The pulse width of an output compare (which resets the free running

counter when TCRE = 1) will measure one more bus clock cycle than 

expected. 



 

The specification has been updated. Please refer to revision V02.07 (04

 May 2010) or later.



In description of bitfield TCRE in register TSCR2,a note has been added:

TCRE=1 and TC7!=0, the TCNT cycle period will be TC7 x "prescaler

counter width" + "1 Bus Clock". When TCRE is set and TC7 is not equal to

0, then TCNT will cycle from 0 to TC7. When TCNT reaches TC7 value, it

will last only one bus cycle then reset to 0.







 

If the PLL is manually turned off (PLLCTL_ PLLON = 0) before a STOP

instruction and the PLL is manually turned on (PLLCTL_PLLON=1) after

execution of the STOP instruction, the PLL might have a premature lock

condition in the case of a STOP instruction being executed with a

pending interrupt and the corresponding interrupt is enabled. In this

case the STOP is executed similar to NOP instruction. 



Due to the manual control of the PLL, the VCO clock is switched on and

off. The PLL lock detection logic uses the VCO clock as well as the

reference clock (based on the external oscillator). The external

oscillator is not stopped because the STOP instruction is executed like

a NOP instruction, which keeps the reference clock running. 



This causes the logic in the PLL lock detection being uncorrelated and

thus resulting in a possible premature LOCK condition (CRGFLG_LOCK=1). 



After the next lock detection cycle the lock is lost (CRGFLG_LOCK=0)

because the VCO clock frequency has not reached the correct value. Some

lock detection cycles later the correct lock condition is reached (VCO

clock frequency reached the correct value) and the LOCK bit is set again

(CRGFLG_LOCK=1). Each transition of the LOCK bit is indicated by the

lock interrupt flag (CRGFLG_LOCKIF). 

Do not modify the PLLON bit around the STOP instruction. 



The clock control and power down/up sequencing is automatically done by

the device CRG module. Only the system clock source selection after exit

from STOP must be controlled by software (CLKSEL_PLLSEL bit) as

described in the Reference Manual. 



Depending on the application if the fast wake-up feature is used the

software also needs to control the bit FSTWKP and bit SCME (both located

in the PLLCTL register) as described in the device Reference Manual when

STOP Mode is entered or exited.





 

In low power modes (stop/p-stop/wait – PSWAI=1) and during PWM PP7

de-assert and when PWM counter reaching 0, the PWM channel outputs

(PP0-PP6) cannot keep the state which is set by PWMLVL bit.  



 

User software can be used to force the port PTP to the same level as

PWMLVL. 

 

When the PWM is used in 16-bit (concatenation) channel and the emergency

shutdown feature is being used, after de-asserting PWM channel 7

(note:PWMRSTRT should be set) the PWM channels do

not show the state which is set by PWMLVL bit when the 16-bit counter is

non-zero. 





 

If emergency shutdown mode is required: 



1) Enable PWM channels in 8-bit unconcatenate mode. 



or 



2) If 16-bit concatenate mode is required user software can force the

appropriate PWM port to the same level as PWMLVL.



 

Configured for Infrared Receive mode, the SCI may incorrectly set the 

RXEDGIF bit if there are consecutive '00' data bits. There are two 

cases:    



Case 1: due to re-sync of the RXD input, the received edge may be 

delayed by one bus cycle. If an edge (bit = '0') is detected near 

an SCI clock edge, the next edge (bit = '0') may be detected one 

SCI clock later than expected due to re-sync logic. 



Case 2: if external baud is slower than SCI receiver, the next edge 

may be detected later than expected.



This glitch can be detected by the RXEDGIF circuit, but it does not 

impact the final data result because the SCI receive and data recovery 

logic takes samples at RT8, RT9, and RT10.

 



 

Case 1 and case 2 may occurs at same time. To avoid those unexpected 

RXEDGIF at IR mode, the external baud should be kept a little bit 

faster than receiver baud by:

                 P > (1/16)/(SBR)

                        or

                 (P)(SBR)(16)> 1



Where SBR is baud of receiver, P is external baud faster ratio. 

For example:

1.- When SBR = 16, P = 0.4%, this means the external baud should be at 

least 0.4% faster than receiver.

2.- When SBR = 4, P = 1.6%, this means the external baud should be at 

least 1.6% faster than receiver.

 

Case 1 will cover case 2, i.e. case 1 is the worst case. If case1 is 

solved, case 2 is also solved.